Energy Logger Pro

Energy Logger Pro Features

• Flexible Expansion for up to 3 FlexSmart Modules and 6 Smart Sensors
• Automatic Detection of Smart Sensors by logger
• Digital Connection of Smart Sensors to logger for Accurate, Reliable Data Collection and Storage
• Multiple Internal and External Power Sources Available for Long-Term Usage
• User-Configurable Sensor Excitation Power and Warmup using Analog Module (#S-FS-CVIA)
• Requires HOBOware Software and USB Kit (PC and MAC Versions)

Energy Logger Pro Specifications

Data Storage Capacity	512K Maximum Storage - Number of Samples Dependant on External Sensors and FlexSmart Modules
Sampling Rate	1 Second to 18 Hours (2-Second Minimum for #S-FS-TRMSA operation)
Sensor Excitation	12 Volts DC at 200 mA total, with User-Programmable Warmup Time on a per-Channel Basis
Logging Modes	Immediate, Timed Delay, or Push-Button Start Options
Memory Modes	Stop When Full; Wrap When Full
LED Indicators	Green: Logging or Standby Red: Low Battery, Storage or Sensor Fail
Sensor Inputs	3 FlexSmart multi-Channel Modules and up to 6 Smart Sensors
Sensor Connectors	6 RJ-12 Smart Sensor Jacks and 3 FlexSmart Module Slots
Communications Type	RS-232 Serial via 3.5mm Serial Port or/and 9-pin D-Sub Connector
Communications Mode	Current Readings while Logging; Read Out While Logging; Read Out When Stopped
Operating Range	Alkaline Battery: -20C to 50C (-4F to 122F) Lithium Battery: -40C to 60C (-40F to 140F)
Battery Life	1 Year Typical Use ( up to 75 mA excitation with 10-minute or longer logging interval and 1-second warmup-time)
Battery	AA Alkaline Batteries (Included)
External Power	13.6 VDC Regulated AC Wall Adapter Connector 9-12 VDC Regulated Wall Adapter (Remove Batteries)
Time Accuracy	0 to 2 Seconds for first data point and ±5 Seconds per Week at 25°C (77°F)
Standards Compliance	CE
Weight	435g (15.23 oz) with Batteries
Dimensions	15.6cm x 8.4cm x 4.6cm (6.13" x 3.31" x 1.81")

NOTE: 1 FlexSmart Analog Module or TRMS Module is Required

The FlexSmart Modules are snap-in signal conditioning units that convert signals from nearly any type of sensor.

FlexSmart Analog (CVIA) Module (#S-FS-CVIA)
>> Flexible DC Signal-Conditioning Module
>> Accepts 2 Channels
>> Input Protection and Signal Filtering
>> Excitation Power to wide range of sensors

Input Channels	2, Single-Ended
Field Wiring	2 or 3 Wire Screw terminals on Detachable Terminal Block, 16 to 24 Gauge (AWG)
Input Range	User-Configurable: 0 to 20 mA DC; 0 to 20 Volts DC (Suitable for 2.5, 5 and 10 Volt Sensors
Input Voltage Range	0 to 24 Volts DC
Input Current Range	0 to 24 mA DC
Minimum Current Source Impedance	< 20 KOhms
Accuracy	± 0.25% of FSR from 50 mV to FSR
ADC Resolution	12 Bits
Power Requirements	+3.3 Volts @ 3mA Active, 6 uA Sleep

TRMS (TRMSA) Module (#S-FS-TRMSA)
>> 2 Channel Input Measurement Module
>> Compatible with Industry-standard Current and Potential Transformers
>> Input Range of 512 mV RMS Full Scale
>> Output Range of 333 mV RMS Full Scale

Input Channels	2
Field Wiring	2 Wire Screw Terminals
Range	5mV to 512mV (Compatible with 333mV FS Output Sensors)
Maximum Input	± 1V
Minimum Input	5mV
Accuracy	± 0.3% of Reading; ± 0.5% FSR
Resolution	15 Bits

NOTE: A Minimum of 1 Sensor is Required

Click on the Measurement below for Available Sensors.

Killowatt Hours (kWh)
Power
True RMS Amperage
True RMS Current and Voltage
DC Amperage
Differential Air Pressure
Gauge Pressure
Barometric Pressure
Relative Humidity
Temperature
Analog Input
Pulse Input
Carbon Dioxide
Wind
Light Intensity
Rain

NOTE: HOBOWare Pro Software is Required

The Energy Logger Pro allows you to monitor and record:
>> HVAC and HVAR
>> Energy Metering and Power Monitoring
>> Facility Monitoring
>> Industrial Machinery Monitoring and Motor Start-Up Analysis
>> Temperature and Humidity Monitoring
>> and alot more ....